Сообщения без ответов | Активные темы Текущее время: 03 июл 2022, 08:56



Ответить на тему  [ Сообщений: 6 ] 
Не получается прошить модуль firepower 5516x 
Автор Сообщение

Зарегистрирован: 01 янв 1970, 03:00
Сообщения: 493
Проблема такая, не могу прошить модуль ФП на асе 5516.
sw-module module sfr recover configure image disk0:/asasfr-5500x-boot-7.0.0-94.img
setup
system install noconfirm http://192.168.0.85/asasfr-sys-7.0.0-94.pkg
и все, жду долго. sfr в recovery
последнее что записал в лог
Цитата:
ISOLINUX 2.10 2004-06-18 Copyright (C) 1994-2004 H. Peter Anvin

Cisco SFR-BOOT-IMAGE and CX-BOOT-IMAGE for SFR - 7.0.0

(WARNING: ALL DATA ON DISK 1 WILL BE LOST)

Loading bzImage...................................................................................................
Loading install.img......
Ready.
[ 0.000000] Linux version 4.18.45-yocto-standard (oe-user@oe-host) (gcc version 8.2.0 (GCC)) #1 SMP PREEMPT Tue May 18 09:25:29 UTC 2021
[ 0.000000] Command line: initrd=install.img console=ttyS0,9600 root=/dev/ram BOOT_IMAGE=bzImage
[ 0.000000] x86/fpu: x87 FPU will use FXSAVE
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000d4adefff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d4adf000-0x00000000d4afffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.8 present.
[ 0.000000] DMI: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.2-0-g33fbe13 by qemu-project.org 04/01/2014
[ 0.000000] Hypervisor detected: KVM
[ 0.000000] last_pfn = 0xd4adf max_arch_pfn = 0x400000000
[ 0.000000] x86/PAT: PAT not supported by CPU.
[ 0.000000] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC- UC
[ 0.000000] found SMP MP-table at [mem 0x000f6430-0x000f643f]
[ 0.000000] RAMDISK: [mem 0x7b410000-0x7fffbfff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F63E0 000014 (v00 BOCHS )
[ 0.000000] ACPI: RSDT 0x00000000D4AE1532 000034 (v01 BOCHS BXPCRSDT 00000001 BXPC 00000001)
[ 0.000000] ACPI: FACP 0x00000000D4AE08DA 000074 (v01 BOCHS BXPCFACP 00000001 BXPC 00000001)
[ 0.000000] ACPI: DSDT 0x00000000D4ADFD40 000B9A (v01 BOCHS BXPCDSDT 00000001 BXPC 00000001)
[ 0.000000] ACPI: FACS 0x00000000D4ADFD00 000040
[ 0.000000] ACPI: SSDT 0x00000000D4AE094E 000B0C (v01 BOCHS BXPCSSDT 00000001 BXPC 00000001)
[ 0.000000] ACPI: APIC 0x00000000D4AE145A 0000A0 (v01 BOCHS BXPCAPIC 00000001 BXPC 00000001)
[ 0.000000] ACPI: HPET 0x00000000D4AE14FA 000038 (v01 BOCHS BXPCHPET 00000001 BXPC 00000001)
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x00000000d4adefff]
[ 0.000000] NODE_DATA(0) allocated [mem 0xd4adb000-0xd4adefff]
[ 0.000000] kvm-clock: cpu 0, msr 0:d4ad9001, primary cpu clock
[ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00
[ 0.000000] kvm-clock: using sched offset of 16214402331 cycles
[ 0.000000] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000d4adefff]
[ 0.000000] Normal empty
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009efff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000d4adefff]
[ 0.000000] Reserved but unavailable: 98 pages
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x00000000d4adefff]
[ 0.000000] Movable zone start for each node
[ 0.000000] ACPI: PM-Timer IO Port: 0x608
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 6 CPUs, 0 hotplug CPUs
[ 0.000000] [mem 0xd4b00000-0xfeffbfff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on KVM
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.000000] random: get_random_bytes called from start_kernel+0x8e/0x44c with crng_init=0
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:6 nr_node_ids:1
[ 0.000000] percpu: Embedded 43 pages/cpu s138520 r8192 d29416 u262144
[ 0.000000] KVM setup async PF for cpu 0
[ 0.000000] kvm-stealtime: cpu 0, msr d4616000
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 857404
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: initrd=install.img console=ttyS0,9600 root=/dev/ram BOOT_IMAGE=bzImage
[ 0.000000] Memory: 3328436K/3484148K available (10252K kernel code, 627K rwdata, 2432K rodata, 1056K init, 404K bss, 155712K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.001000] Preemptible hierarchical RCU implementation.
[ 0.001000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6.
[ 0.001000] Tasks RCU enabled.
[ 0.001000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[ 0.001000] NR_IRQS: 4352, nr_irqs: 472, preallocated irqs: 16
[ 0.001000] Console: colour VGA+ 80x25
[ 0.001000] console [ttyS0] enabled
[ 0.001000] ACPI: Core revision 20180531
[ 0.001000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[ 0.001019] APIC: Switch to symmetric I/O mode setup
[ 0.004000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.004000] tsc: Detected 2416.666 MHz processor
[ 0.004004] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x22d5b7665c1, max_idle_ns: 440795302390 ns
[ 0.005006] Calibrating delay loop (skipped) preset value.. 4833.33 BogoMIPS (lpj=2416666)
[ 0.006004] pid_max: default: 32768 minimum: 301
[ 0.009109] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.011878] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.012069] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.013026] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.014438] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.015006] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.016005] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[ 0.017005] Spectre V2 : Spectre mitigation: kernel not compiled with retpoline; no mitigation available!
[ 0.017007] Speculative Store Bypass: Vulnerable
[ 0.019005] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[ 0.020226] Freeing SMP alternatives memory: 36K
[ 0.023000] smpboot: CPU0: Intel QEMU Virtual CPU version 2.4.0 (family: 0x6, model: 0x6, stepping: 0x3)
[ 0.029019] Performance Events: PMU not available due to virtualization, using software events only.
[ 0.032007] Hierarchical SRCU implementation.
[ 0.037006] smp: Bringing up secondary CPUs ...
[ 0.046037] x86: Booting SMP configuration:
[ 0.047006] .... node #0, CPUs: #1
[ 0.001000] kvm-clock: cpu 1, msr 0:d4ad9041, secondary cpu clock
[ 0.001000] smpboot: CPU 1 Converting physical 0 to logical die 1
[ 0.053052] KVM setup async PF for cpu 1
[ 0.054000] kvm-stealtime: cpu 1, msr d4656000
[ 0.063034] #2
[ 0.001000] kvm-clock: cpu 2, msr 0:d4ad9081, secondary cpu clock
[ 0.001000] smpboot: CPU 2 Converting physical 0 to logical die 2
[ 0.068045] KVM setup async PF for cpu 2
[ 0.069000] kvm-stealtime: cpu 2, msr d4696000
[ 0.078036] #3
[ 0.001000] kvm-clock: cpu 3, msr 0:d4ad90c1, secondary cpu clock
[ 0.001000] smpboot: CPU 3 Converting physical 0 to logical die 3
[ 0.083052] KVM setup async PF for cpu 3
[ 0.084000] kvm-stealtime: cpu 3, msr d46d6000
[ 0.094036] #4
[ 0.001000] kvm-clock: cpu 4, msr 0:d4ad9101, secondary cpu clock
[ 0.001000] smpboot: CPU 4 Converting physical 0 to logical die 4
[ 0.099042] KVM setup async PF for cpu 4
[ 0.100000] kvm-stealtime: cpu 4, msr d4716000
[ 0.110034] #5
[ 0.001000] kvm-clock: cpu 5, msr 0:d4ad9141, secondary cpu clock
[ 0.001000] smpboot: CPU 5 Converting physical 0 to logical die 5
[ 0.115040] KVM setup async PF for cpu 5
[ 0.116000] kvm-stealtime: cpu 5, msr d4756000
[ 0.117016] smp: Brought up 1 node, 6 CPUs
[ 0.118014] smpboot: Max logical packages: 6
[ 0.119006] smpboot: Total of 6 processors activated (28999.99 BogoMIPS)
[ 0.121614] devtmpfs: initialized
[ 0.123264] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.124021] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.125248] xor: measuring software checksum speed
[ 0.137005] prefetch64-sse: 9512.000 MB/sec
[ 0.148004] generic_sse: 8432.000 MB/sec
[ 0.149005] xor: using function: prefetch64-sse (9512.000 MB/sec)
[ 0.151064] NET: Registered protocol family 16
[ 0.153027] audit: initializing netlink subsys (disabled)
[ 0.154093] audit: type=2000 audit(1650894172.443:1): state=initialized audit_enabled=0 res=1
[ 0.156012] cpuidle: using governor ladder
[ 0.158004] cpuidle: using governor menu
[ 0.159085] ACPI: bus type PCI registered
[ 0.160221] PCI: Using configuration type 1 for base access
[ 0.165020] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.184028] raid6: sse2x1 gen() 683 MB/s
[ 0.202013] raid6: sse2x1 xor() 2445 MB/s
[ 0.220014] raid6: sse2x2 gen() 1781 MB/s
[ 0.238013] raid6: sse2x2 xor() 2902 MB/s
[ 0.256015] raid6: sse2x4 gen() 2976 MB/s
[ 0.274010] raid6: sse2x4 xor() 2400 MB/s
[ 0.275005] raid6: using algorithm sse2x4 gen() 2976 MB/s
[ 0.276004] raid6: .... xor() 2400 MB/s, rmw enabled
[ 0.277005] raid6: using intx1 recovery algorithm
[ 0.278263] ACPI: Added _OSI(Module Device)
[ 0.279004] ACPI: Added _OSI(Processor Device)
[ 0.280005] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.281004] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.282005] ACPI: Added _OSI(Linux-Dell-Video)
[ 0.284957] ACPI: 2 ACPI AML tables successfully acquired and loaded
[ 0.287640] ACPI: Interpreter enabled
[ 0.288013] ACPI: (supports S0 S5)
[ 0.289005] ACPI: Using IOAPIC for interrupt routing
[ 0.290028] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.291459] ACPI: Enabled 16 GPEs in block 00 to 0F
[ 0.298438] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.299011] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[ 0.300013] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.301017] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[ 0.302071] PCI host bridge to bus 0000:00
[ 0.303007] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.304006] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.305006] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.306006] pci_bus 0000:00: root bus resource [mem 0xd4b00000-0xfebfffff window]
[ 0.307007] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.322051] pci 0000:00:01.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.323006] pci 0000:00:01.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.324006] pci 0000:00:01.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.325005] pci 0000:00:01.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.327946] pci 0000:00:01.3: quirk: [io 0x0600-0x063f] claimed by PIIX4 ACPI
[ 0.328025] pci 0000:00:01.3: quirk: [io 0x0700-0x070f] claimed by PIIX4 SMB
[ 0.430866] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
[ 0.431208] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11)
[ 0.432195] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11)
[ 0.433194] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11)
[ 0.434105] ACPI: PCI Interrupt Link [LNKS] (IRQs *9)
[ 0.436853] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.437000] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.437009] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.438005] vgaarb: loaded
[ 0.439079] SCSI subsystem initialized
[ 0.440167] ACPI: bus type USB registered
[ 0.441036] usbcore: registered new interface driver usbfs
[ 0.442018] usbcore: registered new interface driver hub
[ 0.443168] usbcore: registered new device driver usb
[ 0.445138] PCI: Using ACPI for IRQ routing
[ 0.447010] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.448040] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.449005] hpet0: 3 comparators, 64-bit 100.000000 MHz counter
[ 0.457114] clocksource: Switched to clocksource kvm-clock
[ 0.458648] pnp: PnP ACPI init
[ 0.460427] pnp: PnP ACPI: found 7 devices
[ 0.478332] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.480747] NET: Registered protocol family 2
[ 0.482176] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.484252] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.486233] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.488092] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.489906] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.491516] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.493323] NET: Registered protocol family 1
[ 0.495068] RPC: Registered named UNIX socket transport module.
[ 0.496640] RPC: Registered udp transport module.
[ 0.497872] RPC: Registered tcp transport module.
[ 0.499101] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.500772] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 0.502361] pci 0000:00:01.0: PIIX3: Enabling Passive Release
[ 0.503891] pci 0000:00:01.0: Activating ISA DMA hang workarounds
[ 0.505587] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.507919] Trying to unpack rootfs image as initramfs...
[ 2.884481] Freeing initrd memory: 77744K
[ 2.885759] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x22d5b7665c1, max_idle_ns: 440795302390 ns
[ 2.890290] Initialise system trusted keyrings
[ 2.891765] workingset: timestamp_bits=40 max_order=20 bucket_order=0
[ 2.896443] NFS: Registering the id_resolver key type
[ 2.897846] Key type id_resolver registered
[ 2.898946] Key type id_legacy registered
[ 2.902787] async_tx: api initialized (async)
[ 2.903976] Key type asymmetric registered
[ 2.905069] Asymmetric key parser 'x509' registered
[ 2.906417] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 2.908331] io scheduler noop registered
[ 2.909377] io scheduler deadline registered
[ 2.910544] io scheduler cfq registered (default)
[ 2.911799] io scheduler mq-deadline registered
[ 2.912988] io scheduler kyber registered
[ 2.914599] ipmi message handler version 39.2
[ 2.915842] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 2.917784] ACPI: Power Button [PWRF]
[ 2.962663] PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 3.050131] PCI Interrupt Link [LNKD] enabled at IRQ 10
[ 3.051609] virtio-pci 0000:00:04.0: virtio_pci: leaving for legacy driver
[ 3.097898] PCI Interrupt Link [LNKA] enabled at IRQ 10
[ 3.099366] virtio-pci 0000:00:05.0: virtio_pci: leaving for legacy driver
[ 3.145827] virtio-pci 0000:00:07.0: virtio_pci: leaving for legacy driver
[ 3.222462] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 3.252229] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 3.282231] 00:06: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[ 3.289911] brd: module loaded
[ 3.293269] loop: module loaded
[ 3.295919] virtio_blk virtio2: [vda] 500118192 512-byte logical blocks (256 GB/238 GiB)
[ 3.300302] vda: vda1 vda2 vda3 < vda5 vda6 vda7 >
[ 3.302516] Uniform Multi-Platform E-IDE driver
[ 3.303755] ide-cd driver 5.00
[ 3.304629] Loading iSCSI transport class v2.0-870.
[ 3.306364] isci: Intel(R) C600 SAS Controller Driver - version 1.2.0
[ 3.308095] megasas: 07.705.02.00-rc1
[ 3.309129] mpt3sas version 25.100.00.00 loaded
[ 3.310641] VMware PVSCSI driver - version 1.0.7.0-k
[ 3.311979] hv_vmbus: registering driver hv_storvsc
[ 3.317848] scsi host0: ata_piix
[ 3.320274] scsi host1: ata_piix
[ 3.321220] ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc0c0 irq 14
[ 3.323027] ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc0c8 irq 15
[ 3.325182] Fusion MPT base driver 3.04.20
[ 3.326297] Copyright (c) 1999-2008 LSI Corporation
[ 3.328114] Fusion MPT SPI Host driver 3.04.20
[ 3.329328] Fusion MPT FC Host driver 3.04.20
[ 3.330513] Fusion MPT SAS Host driver 3.04.20
[ 3.331712] Fusion MPT misc device (ioctl) driver 3.04.20
[ 3.333266] mptctl: Registered with Fusion MPT base driver
[ 3.334714] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 3.336262] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.337971] ehci-pci: EHCI PCI platform driver
[ 3.339157] ehci-platform: EHCI generic platform driver
[ 3.340534] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.342167] ohci-pci: OHCI PCI platform driver
[ 3.343358] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.345108] usbcore: registered new interface driver usbserial_generic
[ 3.346847] usbserial: USB Serial support registered for generic
[ 3.348443] usbcore: registered new interface driver ftdi_sio
[ 3.349943] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 3.351870] usbcore: registered new interface driver pl2303
[ 3.353347] usbserial: USB Serial support registered for pl2303
[ 3.354947] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 3.358261] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.359627] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.361299] mousedev: PS/2 mouse device common for all mice
[ 3.363191] rtc_cmos 00:00: RTC can wake from S4
[ 3.365174] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 3.366734] rtc_cmos 00:00: registered as rtc0
[ 3.368958] rtc_cmos 00:00: alarms up to one day, 114 bytes nvram, hpet irqs
[ 3.371574] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.373175] usbcore: registered new interface driver usbhid
[ 3.374639] usbhid: USB HID core driver
[ 3.375665] hv_vmbus: registering driver hv_balloon
[ 3.377145] Initializing XFRM netlink socket
[ 3.378494] NET: Registered protocol family 10
[ 3.380125] Segment Routing with IPv6
[ 3.381225] NET: Registered protocol family 17
[ 3.382436] Key type dns_resolver registered
[ 3.384467] mce: Using 10 MCE banks
[ 3.385445] sched_clock: Marking stable (3385404442, 0)->(4022500052, -637095610)
[ 3.387887] registered taskstats version 1
[ 3.388994] Loading compiled-in X.509 certificates
[ 3.395476] Loaded X.509 cert 'Build time autogenerated kernel key: f9382c07d8aaca6feec94b551a46ce04e8631b80'
[ 3.401159] Key type encrypted registered
[ 3.402453] console [netcon0] enabled
[ 3.403440] netconsole: network logging started
[ 3.404854] rtc_cmos 00:00: setting system clock to 2022-04-25 13:42:55 UTC (1650894175)
[ 3.480228] ata1.00: ATA-7: QEMU HARDDISK, 2.4.0, max UDMA/100
[ 3.481805] ata1.00: 6291456 sectors, multi 16: LBA48
[ 3.488207] ata2.00: ATAPI: QEMU DVD-ROM, 2.4.0, max UDMA/100
[ 3.494145] scsi 0:0:0:0: Direct-Access ATA QEMU HARDDISK 0 PQ: 0 ANSI: 5
[ 3.496708] sd 0:0:0:0: [sda] 6291456 512-byte logical blocks: (3.22 GB/3.00 GiB)
[ 3.498723] sd 0:0:0:0: [sda] Write Protect is off
[ 3.500055] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.502786] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.504096] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.506464] scsi 1:0:0:0: CD-ROM QEMU QEMU DVD-ROM 2.4. PQ: 0 ANSI: 5
[ 3.510201] sr 1:0:0:0: [sr0] scsi3-mmc drive: 4x/4x cd/rw xa/form2 tray
[ 3.511995] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.514119] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.517145] Freeing unused kernel image memory: 1056K
[ 3.518568] Write protecting the kernel read-only data: 16384k
[ 3.521473] Freeing unused kernel image memory: 2012K
[ 3.523664] Freeing unused kernel image memory: 1664K
INIT: version 2.88 booting
mount: /proc: none already mounted on /proc.
[ 3.993063] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input3
Starting udev
[ 4.583521] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.585916] udevd[124]: starting eudev-3.2.5
[ 4.612105] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.614743] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.804990] failover: module verification failed: signature and/or required key missing - tainting kernel
[ 4.811236] virtio_net virtio0 cplane: renamed from eth0
Configuring network interfaces... done.
urandom start: failed.
Starting haveged random number generatorhaveged: command socket is listening at fd 3
.
INIT: Entering runlevel: 3
Starting ntpd: done
[ 5.275032] random: crng init done
[ 5.275993] random: 1 urandom warning(s) missed due to ratelimiting
[ 319.956838] Floppy drive(s): fd0 is 1.44M, fd1 is 1.44M
[ 319.972714] FDC 0 is a S82078B
[ 321.103540] vda: vda1
[ 321.111969] Adding 4194300k swap on /dev/vda1. Priority:-2 extents:1 across:4194300k
[ 1189.169976] EXT4-fs (vda5): mounting ext3 file system using the ext4 subsystem
[ 1189.175572] EXT4-fs (vda5): mounted filesystem with ordered data mode. Opts: (null)
[ 1189.216331] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 1189.222171] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 1189.266681] EXT4-fs (vda7): mounting ext3 file system using the ext4 subsystem
[ 1189.270480] EXT4-fs (vda7): no journal found
[ 1573.003426] vda: vda1
[ 1573.011288] Adding 4194300k swap on /dev/vda1. Priority:-2 extents:1 across:4194300k

(process:1664): GLib-ERROR **: /local/jenkins/workspace/fxplatform/Builds/release__2.8.1_fcs_jubilee/build-smp-compile/fxos/linux/wrlinux/bitbake_build/tmp/work/corei7-64-wrs-linux/glib-2.0/1_2.54.3-r0/glib-2.54.3/glib/gmem.c:100: failed to allocate 1048576 bytes


***
*** EVENT: The module is being automatically restarted.
*** TIME: 17:14:21 AST Apr 25 2022
***


***
*** EVENT: Start Parameters: Image: /mnt/disk0/vm/vm_1.img, ISO: , Num CPUs: 6, RAM: 3403MB, Mgmt MAC: 70:B3:17:79:49:DE, CP MAC: 00:00:00:02:00:01, HDD: -drive file=/dev/sda,cache=none,if=virtio, Dev Driver: virtio
*** TIME: 17:14:21 AST Apr 25 202

***
*** EVENT: Start Parameters Continued: RegEx Shared Mem: 0MB, Cmd Op: , Shared Mem Key: 8061, Shared Mem Size: 64, Log Pipe: /dev/ttyS0_vm1, Sock: /dev/ttyS1_vm1, Mem-Path: -mem-path /hugepages
*** TIME: 17:14:21 AST Apr 25 2022
***

(process:1983): GLib-WARNING **: /local/jenkins/workspace/fxplatform/Builds/release__2.8.1_fcs_jubilee/build-smp-compile/fxos/linux/wrlinux/bitbake_build/tmp/work/corei7-64-wrs-linux/glib-2.0/1_2.54.3-r0/glib-2.54.3/glib/gmem.c:483: custom memory allocation vtable not supported
WARNING: Image format was not specified for '/mnt/disk0/vm/vm_1.img' and probing guessed raw.
Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted.
Specify the 'raw' format explicitly to remove the restrictions.
WARNING: Image format was not specified for '/dev/sda' and probing guessed raw.
Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted.
Specify the 'raw' format explicitly to remove the restrictions.
WARNING: Image format was not specified for '/mnt/disk0/.private/meta_vm_data' and probing guessed raw.
Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted.
Specify the 'raw' format explicitly to remove the restrictions.
Status: Mapping host 0x7f6d5a400000 to VM with size 67108864
Warning: vlan 0 is not connected to host network


25 апр 2022, 17:36
Профиль

Зарегистрирован: 01 янв 1970, 03:00
Сообщения: 493
Достал ssd прогнал ее родной утилитой от микрона - все ок, ошибок нет.
Попробовал вставить не родную ssd - результат такой же (ошибок по не оригинальной ssd не пишет)
Так же пробовал версию 6.7 зашивать - тоже самое


25 апр 2022, 17:54
Профиль

Зарегистрирован: 29 май 2017, 21:19
Сообщения: 1363
бросьте вы эту затею SFR уже давно списан - используйте данное железо просто как АСА


25 апр 2022, 21:52
Профиль

Зарегистрирован: 01 янв 1970, 03:00
Сообщения: 493
firepower как ips работает хорошо. Не понятно в чем проблема, в самой асе или ssd. еще и смарт не вовремя отключили (


26 апр 2022, 11:39
Профиль

Зарегистрирован: 29 май 2017, 21:19
Сообщения: 1363
FPR как IPS да работает если у вас есть все лицензии и то в нормальном нативном режиме FTD

SFR как сервис на АСЕ уже давно умер - и для его работы также требуются соотв. лицензии


26 апр 2022, 12:37
Профиль

Зарегистрирован: 01 янв 1970, 03:00
Сообщения: 188
ROMMON обновляли до последней версии?


27 апр 2022, 08:31
Профиль
Показать сообщения за:  Поле сортировки  
Ответить на тему   [ Сообщений: 6 ] 

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 4


Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете добавлять вложения

Найти:
Перейти:  
Создано на основе phpBB® Forum Software © phpBB Group
Designed by ST Software for PTF.
Русская поддержка phpBB